Acclimation

Acclimation is not required. COREtec Pro can be installed and walked on the same day in a climate-controlled space — no waiting period.

Pro tip: If boxes have been stored in a cold truck or warehouse below 50°F, let them sit in the install room for 24 hours before cutting. Rigid-core planks tolerate temperature change better than wood, but extreme cold can make the click-lock edges brittle during installation.

Subfloor flatness

Subfloor must be clean, structurally sound, flat to within 3/16 inch over 10 feet, and free of debris, paint, oil, wax, and old adhesive residue.

Pro tip: On older concrete slabs, we measure flatness in multiple directions — not just one straight line. A 3/16-inch dip in a 2-foot circle under a refrigerator telegraphs through even the thickest SPC eventually, regardless of what the 10-foot average says.

Moisture testing (concrete)

On concrete subfloors, perform a calcium chloride or in-situ relative humidity test per ASTM F1869 / ASTM F2170. The result must fall within Shaw’s published moisture limits in the COREtec Pro install guide.

Pro tip: Bay Area homes near the water (Alviso, parts of San Mateo, coastal San Francisco) often have higher slab moisture than the test-day reading suggests — slab moisture fluctuates seasonally. If your slab tests at 85% RH in October, it may hit 95% in February. Budget for the 6-mil moisture barrier below either way.

Moisture barrier (concrete subfloors)

A 6-mil polyethylene moisture barrier is recommended over below-grade or concrete subfloors per ASTM F710.

Pro tip: We recommend 6-mil polyethylene vapor barrier over every concrete subfloor regardless of test results. Seasonal moisture shifts, future plumbing leaks, and unseen slab cracks mean a clean moisture test today doesn’t guarantee a dry subfloor in five years. 6-mil poly is $30-50 for a whole room — inexpensive protection. Overlap seams by 6-8 inches, seal with waterproof tape, run 2-4 inches up the walls (hidden by baseboard). This is industry-standard per NWFA and what we’d do in our own home.

Underlayment (do not replace the attached pad)

No additional underlayment is needed — COREtec Pro Enhanced ships with attached cork pad.

Pro tip: Customers sometimes ask about adding a thicker pad under Enhanced for more softness. Don’t. Enhanced ships with a cork pad already factory-attached to the SPC core — this is the only approved underlayment, and adding any second pad creates an unstable stack-up that causes click-lock seam failure over time. The warranty specifically voids structural-integrity coverage if a non-manufacturer pad is used.

Installation method

Floating angle-tap click installation is the standard method. Direct glue-down is also approved per the Shaw COREtec Pro install guide.

Pro tip: For rooms wider than 25 feet or longer than 40 feet continuous, add a T-molding expansion break. SPC is dimensionally stable but not dimensionally inert — large rooms need room to breathe. Ignore this on thicker SPC at your peril; the extra thickness makes seam pressure more pronounced when expansion has nowhere to go.

Radiant heat compatibility

Compatible with radiant heat systems. Maximum surface temperature must not exceed 85°F.

Pro tip: Turn the heating system on at least two weeks before installation to purge slab moisture. After installation, raise temperature in 5°F increments per day back to operating level. Never go from room-temp to full heat in one day — thermal shock can compromise the click-lock edges and cork pad adhesion.

Daily maintenance

Use a pH-neutral hard-surface cleaner — Shaw recommends their Encore floor cleaner. Sweep or dry-mop regularly to remove grit; damp-mop with approved cleaner as needed. Do not use treated dust mops; they can leave residue that dulls the finish over time.

Pro tip: Use a cleaner specifically labeled for luxury vinyl or SPC — Bona Pro Series Luxury Vinyl Floor Cleaner works well. Avoid ‘mop and shine’ products that leave a film; they trap dirt and dull the Ceramic Bead finish over time.

What to avoid

Avoid wax, polish, vinegar, citrus solvents, oil soap, and abrasive scrubbing pads. Do not use rotating-beater-bar vacuums, and skip steam mops unless explicitly approved for the specific COREtec product.

Pro tip: Steam mops are the #1 warranty-void cause on COREtec Pro floors — COREtec Pro’s master warranty explicitly denies coverage for any damage caused by steam cleaners, and the moisture/heat breaks down the adhesives in the plank construction. Customers sometimes say ‘but it’s waterproof’ — the core is waterproof; the seams and adhesives are not designed for pressurized hot water.

Furniture and pet protection

Use felt protectors on furniture legs and non-staining floor protectors under heavy furniture, chairs, and tables. Use walk-off mats at exterior entries to capture grit.

Pro tip: Office chairs with plastic wheels are harder on SPC than pet claws. COREtec Pro’s warranty specifically excludes damage from caster wheels unless they’re wide rubber — swap plastic wheels for rubber or silicone, or use a chair mat. This is in the written warranty, not a suggestion.